Irrigation bypass valve-manufacture,factory,supplier from China

16mm double lock-nut bypass valve and double thread bypass switch are made of high-quality engineering plastics. The products are of high quality and durable. This kind of drip irrigation bypass switch adopts double thread form with tight connection, good water locking effect and no water leakage.Installation steps: drill 8 mm hole in the main water supply pipe, insert the bypass valve, rotate the lock-nut, and connect the 16mm end with the drip irrigation tape. Tip: after drilling holes on PE pipe and plastic hose, directly insert and install it.

Product features: soft tape bypass valve has its own valve, which can control and adjust the flow of each drip irrigation tape at will.Precautions for installation: 1. mainly used for connection of main water tape, PE water tape(wall thickness 0.6-1.6mm), etc.2.The fittings of this specification are connected between the soft drip irrigation tapes with inner diameter of 16mm.

Usage: first, use special puncher to punch holes on the side of soft water tape, then rotate the bypass valve of the product into the hole of soft tape, tighten the screw to fix the bypass valve on the soft water tape, and connect the drip irrigation tape on the other side.

Lock-nut bypass parameterNameLarge hole lock-nut bypassSpecifications16-16mm  12-16mmPackageBaggedQuantity2000 pieces/ bagSales modelWholesale, agencyMaterialSpecial materials have strong aging resistanceApplicable conditionsThe main pipes are PE irrigation pipe and PVC irrigation pipe

Instructions for use: Mainly used for capillary head end control (the right end of the pull ring is connected to a 16mm drip tape, which is fixed by the pull ring; the left end is connected to the water delivery main pipe, which can be used for PE pipes (wall thickness greater than 1mm), water delivery tape or use with matching rubber bands , Connect with pvc pipe.)Product introduction: The pull-ring bypass switch is a commonly used drip irrigation switch.

Features: drip irrigation tape can connect main pipe (water tape) instantly. The bypass has its own valve, and the water flow can be adjusted at will.Precautions for installation:1.It is mainly used for connection of main water tape, PE water tape(wall thickness 0.7-3.0mm), etc.

Installation and usage: the product is used in the project of PE small pipe or drip irrigation pipe. Compared with the traditional PE socket straight through and bypass, the advantages are that the user can adjust the switch of each irrigation pipe tape and increase the controllability of the system.through is made of new engineering plastics, with beautiful appearance, strong anti-aging performance, low cost and long service life. Scientific design, convenient connection, easy disassembly, strong flexibility, good sealing, beautiful and practical, and easy to install and use, easy to recycle.

Instructions for use: used for the connection and front-end control of the water delivery belt and the drip irrigation belt (one end of the valve is connected to a 16mm drip irrigation belt, which is fixed by a screw lock; the other end is connected to the main water delivery belt)How to use: First use a hole punch (14mm in diameter) to punch holes on the side of the soft water belt, then rotate the bypass valve of the drip irrigation belt into the hole of the soft belt, tighten the nut to fix the bypass on the soft water belt, and on the other side Just connect the drip tape.

Drip irrigation : The inlaid drip irrigation pipe is an integrated drip irrigation pipe with a cylindrical dripper embedded on the inner wall of the pipe. The dripper is assembled on the inner wall of the pipe while producing the pipe, which is easy to install and use.Classification1. According to the water outlet method, it is divided into:Pressure Compensated Drip Irrigation Pipes and Non-Pressure Compensated Drip Irrigation Pipes2. According to the structure can be divided into:In-line drip irrigation pipe and inter-pipe drip irrigation pipeapplicationApplicable conditions:1.

Product features:It is made of new engineering plastics, with aging-resistant process and materials, long service life, mainly supporting export products.Scientific design, high strength, good sealing, convenient connection, easy disassembly, strong flexibility, easy recycling, beautiful appearance.It is mainly applicable to the irrigation of vegetables, fruit trees, shrubs, nurseries and other ground crops, and can be used for tree crown cooling and tree frost preventionSpraying and drip irrigation of plant cooling, urban environmental protection, lawn and other aspects.Instruc

 It is suitable for PE water supply pipe and PVC water supply pipe as the main pipe of drip irrigation. The branch pipe is suitable for 16mm PE coil pipe, 16 drip irrigation pipe, micro-spray irrigation 16 capillary pipe 16 PE pipe, etc.Installation steps: drill 8 mm hole in the main water supply pipe, insert the bypass valve, rotate the lock-nut, and connect the 16mm end with the drip irrigation tape. Tip: after drilling holes on PE pipe and plastic hose, directly insert and install it.

PE socket straight through valve is widely used in agricultural water-saving irrigation project. For example, small pipe outflow project and drip irrigation system (drip irrigation pipe), some projects that use PE pipes, and PEΦ16 or 20 capillary drip irrigation systems, etc.Through is made of new engineering plastics, with beautiful appearance, strong anti-aging performance, low cost and long service life. Scientific design, convenient connection, easy disassembly, strong flexibility, good sealing, beautiful and practical, and easy to install and use, easy to recycle.

Product introduction: the pull ring bypass switch is a common drip irrigation switch, one end of which is connected with the main water tape or PE pipe, and the other end is connected with the drip irrigation tape, so as to achieve the effect of controlling the water flow in the rear section of the valve.Instructions for use: it is mainly used for controlling the head end of the capillary (the right end of the pull ring is connected with a 16mm drip irrigation tape, which is fixed by the pull ring; The left end is connected with main water delivery pipe, which can be used for PE pipe (wal

There are two types of drip irrigation tape lock-nut bypass produced by our factory, one is 12-16mm reversed lock bus bypass, the other is 16-16mm reversed lock-nut bypass. Generally, users call this kind of reversed lock-nut bypass as drip irrigation tape lock-nut bypass. 16-16mm lock-nut bypass is also called large hole lock-nut bypass or large body lock-nut bypass. Because both ends are 16mm diameter, this large hole lock-nut bypass is a kind of bypass that is more commonly used in lock-nut pipe fittings.

Product features: scientific design, high strength, good sealing, convenient connection, easy disassembly, strong flexibility, easy recycling, and beautiful appearance. It is made of engineering plastics and has a long service life.

Functions: 1. On-off valve 2. Regulating flow 3.

The drip irrigation belt uses a plastic pipe (drip irrigation pipe lead) to send water through the orifice or dripper on the capillary tube with a diameter of about 10mm to the root of the crop for local irrigation. It is a dripper or drip irrigation belt with a very small outlet orifice, which drips water evenly and slowly into the soil near the roots of the crops.1. The built-in dripper has its own filter window, which has good anti-blocking performance.2. Turbulent flow channel design. Water evenly.3. The dripper and pipeline have strong integrity,4.

Product features:Connect 16 / 20mm PE pipe and butt with 16 / 20 mm PE pipeHigh strength product16/20MM socket-typeFunctions: 1. On-off valve 2. Regulating flow 3.

Functional features:Communication mode of solenoid valve: WBUS (2-wire system, no polarity, 3km)HMI: 12.1"touch screen displayMultiple irrigation areas: maximum 120, single area irrigation time in irrigation area: 4 stagesIt can be irrigated at regular time and quantitatively, or the irrigation can be set up according to temperature and solar radiation4 start times can be set for each irrigation area every day4 filter backwash (4 dry contacts) can be controlled at regular timeEmergency irrigation: one-key irrigation function (emergency irrigation)Temporary stop: one-key sto

The pressure compensation drip irrigation pipe is made of high-density PE pipe with improved nanotechnology and built-in pressure compensation emitter. It is suitable for complex terrain and has the characteristics of good uniformity, strong anti-clogging ability and long service life.The commonly used model of pressure compensation drip irrigation pipe is Φ16. The distance between the emitters is 300mm (200), the wall thickness is 0.6mm, 0.8mm and 1.0mm.

Performance characteristics: wider water path, the water flow is in a turbulent state and there are multiple inlets into the labyrinth, which has strong anti-clogging ability; the main pipeline on the ground is a black water delivery tape or pipe array, which is suitable for drip irrigation in greenhouses and fields.Technical parameterPipe diameter [mm)Distance between emitters (mm)Pressure (Mpa)Flow rate (L/H)Length of laying (m)Diameter 20300（adjustable)0.02 -0.082、3、4≤150Diameter 16300（adjustable)0.02 -0.082、3、4≤100Diameter 12300 (adjustable

Suitable for spray irrigation and drip irrigation 16mm PE pipePurpose: used for 16mm PE pipe connecting PE main pipe, PVC main branch bypass joint switch

The built-in patch drip irrigation tape has the following characteristics:The built-in patch drip irrigation tape has many kinds of drip hole spacing for customers to choose, and can customize drip irrigation tape with different plant spacing for customers, so as to ensure that the drip irrigation tape meets the requirements of customers for all planting spacing.The outer diameter of the product is 16mm, and the wall thickness is divided into three types: 0.2/0.3/0.4mm (normal working pressure is 0.08MPa-0.1MPa, and the flow rate of emitter is 2L/h). It can b