Y-type 50 Net Filter-manufacture,factory,supplier from China

1. Check the condition of the pressure gauge to see if it is working properly.2. Check the pressure values of pressure gauge 1 and pressure gauge 2, when the difference between the pressure values of the two pressure gauges exceeds 0.02GP, clean the filter screen.

Precise filtration: Filter discs with exceptional precisions may be selected in step with the water requirements. There are 20 microns, 55 microns, one hundred microns, 130 microns, two hundred microns, 400 microns and other specifications, and the filtration ratio is extra than 85%.Thorough and efficient backwashing: Because the filter pores are completely opened during backwashing, and the centrifugal jet effect is added, the cleaning effect that other filters cannot achieve can be achieved.

When the filter is working normally, the pressurized water flows into the tank from the water inlet and reaches the filter layer evenly. When the water flows through the filter layer, the impurities are filtered and retained. There is a water trap with a valve at the bottom of the filter, and the filtered water is collected evenly and then flows out of the filtering equipment.With the continuous accumulation of impurities in the filter layer, the water flow loss continues to increase.

The stack clean out is composed of a hard and fast of plates with grooves on each sides. the intersection point shaped with the resource of the rims of the grooves can intercept the solids in the water.

Drip irrigation has been developed for nearly a century since its birth. As a new type of irrigation technology, it has shown its water-saving ability, especially in countries and regions with severe water shortages. A water-saving irrigation technology combined with drip irrigation technology. Drip irrigation uses a pipeline system to supply water, so that the irrigation water is dripped, slowly, uniformly, regularly and quantitatively infiltrating the root development area of the crop, so that the soil in the main root area of the crop is always maintained* Hydrated state.

Components used in drip irrigation (listed in order from water source) include: Pump or pressurized water source. Water filter(s) or filtration systems: sand separator, Fertigation systems (Venturi injector) and chemigation equipment (optional) Backwash controller (Backflow prevention device)

Features of sheet type drip irrigation belt　1、Integrated flat drip head drip irrigation belt is an integrated drip irrigation belt with flat-shaped drip head set on the inner wall of the pipe belt, which is widely used in greenhouse greenhouses and irrigation of cash crops in large fields. 　　2、The drip head is integrated with the pipe belt, easy to install and use, low cost and low investment. 　　3、Drip head has self-filtering window, good anti-clogging performance. 　　4、Using labyrinth flow channel, with a certain pressure compensation effect.

The pipe joint with three openings is called tee pipe. Tee pipe is widely used in the pipe network conveying liquid and gas. Due to different conveying media, the material of tee pipe is divided into: cast copper, cast aluminum, plastic, cast iron, cast steel, glass, etc. tee is also widely used.Introduction:As the name suggests, there are three openings, i.e. one in and two out, or two in and one out. It is a kind of chemical pipe fittings, T-shaped and Y-shaped. It has equal diameter nozzle and reducing nozzle. It is used for the collection of three identical or different pipelines.

1. AdvantagesSave water, fertilizer and laborDrip irrigation is a full pipeline water delivery and local micro-irrigation, which reduces the leakage and loss of water to the lowest limit. At the same time, because it can supply the water required by the crop root zone in a timely manner, there is no problem of peripheral water loss, and the water use efficiency is greatly improved. Irrigation can be conveniently combined with fertilization, that is, dissolve the chemical fertilizer and pour it into the irrigation system.

The Merits of Drip IrrigationAdvantages of any kind of watering rely On the types of vegetation grown, how properly the Weather behaves, and the plant overall performance You preference.

In recent years, there are a variety of popular orchard irrigation methods, such as immersion irrigation, manual irrigation, water-saving irrigation, high-level sprinkler irrigation, and simple sprinkler irrigation. However, these technologies all have their shortcomings more or less. The cost of immersion irrigation is high, and the cost of manual irrigation is high. The effect is relatively poor. Water-saving water-saving irrigation has low one-time investment, high water-saving efficiency, simple maintenance in the later stage, and high-level sprinkler irrigation.

Of course, while used on the perfect crop, drip irrigation has some of key benefits:It may function at a decrease strain;In case you are developing a crop like pumpkin and watermelon with a extensive spacing, you don’t waste water on areas where there's no root device to take it up;It is good for vegetation in which wetting the leaves can motive disease. this makes it the favoured system for tomatoes and crops grown in tunnels;It's miles important when plastic mulch is used to cowl the soil.Dripper tubes come in various forms.